The pressure settings of the pneumatic transport system directly affect the energy consumption of the process, the lifespan of the wear parts, and the overall operational reliability of the line. Misadjusted pressure means, in practice, either clogged pipelines or excessive wear and unnecessary energy loss. In this guide, we will go through step by step how to optimize pressure settings correctly in bulk material transport.
If you are planning to implement pneumatic transport or want to understand what kinds of solutions are available, please read on. for pneumatic conveying before you start the adjustment work.
Starting data before adjusting the pressure settings
Before you touch any of the controls, you need to have the necessary input data at hand. Pressure settings cannot be optimized in a vacuum: each variable affects the other, and without a thorough initial state mapping, you easily end up guessing instead of making informed decisions.
Collect the following information before starting the adjustment work:
- Material properties bulk density, particle size, moisture content, flowability and flow properties
- Pipework geometry Total length of the pipeline, diameter, elevation differences and number of bends
- Capacity requirement: the required transfer quantity in tons per hour
- Transport method: do you use dense phase transport (TP) or dilute phase transport (DP)?
- Available compressed air output: Maximum pressure and flow rate of the compressor
- Operating temperature: Especially when handling hot materials, the temperature affects the air density and thus the transportability.
Once this information is available, you can move on to the actual adjustment work in a systematic manner. Incomplete input data is the most common reason why test runs fail or the system does not reach the planned capacity.
Determine the correct transport pressure according to the material
Selecting the transport pressure is the most important single step in the entire optimization process. Too low a pressure leads to material accumulation in the piping and blockages. Too high a pressure, on the other hand, increases energy consumption, increases material degradation, and consumes the piping and components unnecessarily quickly.
The material largely determines the pressure range at which you should operate. Use the following principles as a starting point:
- Fine-grained and lightweight materials (e.g., dusty materials, light granules): are often suitable for aerial transport, where the typical operating pressure is lower and the material speed in the pipeline is high.
- Heavy, consuming or easily perishable materials (e.g. additives, boiler dust, soot): are best suited for pipe transport, where the pressure can be 1–7 bar and the material velocity in the pipeline is low (7–10 m/s), which significantly reduces wear.
- Long distance travel and high altitudes increase the pressure requirement: calculate the pressure loss of the piping system by taking into account the friction losses in the straight pipe, the additional losses at the bends, and the static pressure caused by the altitude difference.
Set the transport pressure so that it covers the calculated pressure loss and leaves a sufficient margin of safety, but does not exceed it unnecessarily. Use the material’s adhesion load ratio (µ) as a guide: in a plug transport, the goal is typically a value of over 15, which means an efficient material-air ratio and low operating costs.
Adjust the air flow and pressure difference to balance the system
After determining the transport pressure, it is time to adjust the air volume and pressure difference to create a functioning whole. These two variables are in close interaction: increasing the air volume increases the material’s speed in the pipeline, but at the same time reduces the pressure difference. The goal is to find a point of equilibrium where the material moves smoothly without clogging but also without excessive wear.
The adjustment basically proceeds as follows:
- Set the starting pressure based on material calculations for the compressor or pressure vessel.
- Check the settings of the fluidization system: The duration and frequency of the fluidization pulse affect how the material is distributed in the plug in the pipeline. A shorter pulse interval densifies the plug, a longer one rarefies them.
- Track the pressure difference between the beginning and end of the pipeline: The pressure difference should remain constant during the transport period. Sudden spikes indicate a buildup of material or blockage.
- Adjust the air flow in steps Take small steps and record each change. Don't make multiple changes at the same time, because then you won't be able to distinguish which change affected which.
- Check the readings of the pressure gauges in the piping system from several points, if possible. A local deviation can reveal a point where the pipeline is partially blocked or where air passes through the material.
When the air volume and pressure difference are balanced, the transport period is uniform and predictable. This is reflected in practice in that the pressure tank empties out in a steady manner and no sudden pressure spikes or alarms occur during the process. A good balance also reduces the compressor load and, therefore, energy consumption.
If you want to see how different materials and process conditions affect the system's design in practice, Our reference provide concrete examples of demanding objects.
Check and validate the settings during the trial run
Computational values and adjustment work create a good foundation, but real validation always occurs through testing. The operation of the pneumatic transport system depends on so many variables that, in theory, seemingly correct settings may still require fine-tuning in practice.
Conduct the trial run systematically as follows:
- Start with a lower capacity as a target value. This gives flexibility to react to problems before the system is under full load.
- Track the duration of the transport period and compare it with the calculated value. A significant deviation indicates either an incorrect pressure setting or a problem with the piping system.
- Write down the pressure meter readings From the beginning of the transport period to the end. A smooth curve is a sign of a functioning setup. Uneven curves or spikes indicate problems.
- Increase capacity gradually Set the target value and check that the system operates stably at all load levels.
- Check the worn parts After the test drive: the pipe bends, valves, and the inner surfaces of the pressure vessel indicate whether the pressure and speed are at the correct level or whether some setting is causing excessive wear.
After the test drive, document all final settings carefully. This is important for both future maintenance and situations where the system must be restarted after a long standstill. Well-documented settings significantly shorten the start-up time and reduce the risk of human errors.
The optimized pneumatic conveying system operates smoothly, consumes energy efficiently, and requires little maintenance. If you want to deepen your understanding of pneumatic conveying sizing and technology options, please learn more to pneumatic conveying solutions. Kopar designs and manufactures pneumatic conveyors for the most demanding industrial processes, and we are happy to help you find a solution that suits your process requirements. Contact us and tell us more about your needs.

You have a challenge that needs solving?
Let us help! Contact us for more information about our products and services.