9.10.2026

How to choose the right cooling solution for a hot and demanding mineral material?

Hot and abrasive mineral materials place demands on cooling equipment that conventional industrial cooling solutions cannot always meet. Calcine, bottom ash, burnt lime and slag granules may enter the cooling stage at temperatures of several hundred degrees Celsius, while their abrasive nature can rapidly wear down equipment if the wrong technology is selected. Choosing the right cooling solution is not merely a technical detail; it has a direct impact on the reliability, safety and operating costs of the entire process.

In this guide, we go through how to select the most suitable cooling technology for a hot mineral material through three key stages: evaluating material properties, comparing technologies, and finally designing the overall integration. to our cooling solutions already at this stage, if you want a concrete idea of the available options.

Material properties as a starting point for choosing a cooling solution

Before making technology choices, carefully assess the properties of the material under consideration. This step is the foundation of the entire selection process, as incorrect assumptions easily lead to under- or over-sized equipment, shorter operational life, and unexpected production interruptions.

Collect the following information about the material under consideration before comparing any alternative options:

  • Incoming temperature: How hot does the material get before it enters the cooling phase? The slag and bottom ash can come from the process at temperatures of up to 700-900 °C, while the process dust may be cooler.
  • Required output temperature: To what temperature must the material be brought to? This is influenced by subsequent processing steps, HSE requirements, and possible transport restrictions.
  • Material consumption: Hard, rough, or sharp materials wear the surfaces of the cooling device quickly. Evaluate the material's abrasiveness, as it largely determines the types of surface materials and structural solutions you need.
  • Particle size and flow properties: Fine-grained dusty material behaves differently than coarse-grained material. Fine-grained materials can become fluidized or clog the device if the structure does not take this into account.
  • Capacity (t/h): The requirement for completing the process determines the size of the chiller and whether one or more parallel units are needed.
  • Moisture content and chemical composition: Certain materials, such as burnt lime, react with moisture. Their chemical properties may limit the design of the cooling water circuit or require special surface treatments.

Once you have this information, you have a clear picture of the kind of stresses the cooling system will have to withstand. Checkpoint: If you cannot answer all the points above, obtain the missing data from process measurements or from the material supplier before proceeding to the next step. Technology choices made with incomplete input data almost always lead to problems during operation.

Compare cooling technologies according to process conditions

After determining the material’s properties, you can proceed to compare the available cooling technologies. Industrial cooling uses a variety of devices that operate on different principles; the right choice depends on how well the technology’s operating principle fits the requirements set by the material and process.

Below is an overview of the most common technologies and their suitability:

  • Cooling drums (rotary coolers): Suitable for coarse and medium-heavy materials. The rotating structure effectively mixes the material and enables a long retention time. The cooling drum is a traditional choice for cooling punches and dies in melting processes, for example.
  • Cooling screws: A compact solution that is well suited for smaller capacities and situations where space is limited. However, with consumable materials, screw wear is a significant challenge, which increases maintenance costs.
  • Rotary high-pressure screw-based coolers (such as the KRC series): Patented design that combines high cooling performance and extremely low wear rate. Specifically suitable for extreme temperatures, such as cooling the bottom of a tank from 900 °C to approximately 200 °C. The modular design significantly simplifies maintenance compared to traditional screw-type coolers.
  • Refrigerated forklift trucks: A good option in situations where material needs to be transported further during cooling. Ideal for high-temperature materials that cannot be easily handled in rotating equipment.

When comparing technologies, place them side by side against the material’s input data. Ask about each option: Does the structure withstand the material’s abrasion? Is the cooling capacity sufficient to achieve the required temperature change? What are the maintenance costs over the lifetime of the system? A point of check: if any technology requires a compromise on more than one of these criteria, it is probably not the right choice for your process. From our references You will see how different technologies have been applied in similar processes around the world.

Also remember that in a single process, multiple cooling technologies may need to be used in succession or in parallel. For example, first rough pre-cooling at a high temperature and then fine-tuning to the final output temperature are often a more sensible solution than one overloaded device. Contact our experts, If you want help with comparing technologies to your own process.

Consider integration and reliability in the overall solution

The selection of an individual cooling device is only part of the whole picture. For the cooling solution to function reliably as part of a broader process, it must be carefully designed in conjunction with the other process stages. Integration directly affects how well the entire line operates without disruption and how easily the system can be maintained.

Go through the following integration factors before making a final decision:

  1. Feeding arrangement: How does the hot material move from the previous process step to the cooler? The feed must withstand high temperatures and be able to deliver the material uniformly so that the cooler operates optimally.
  2. Removal transport: The material exiting the cooler must be smoothly directed to the next process step or storage. Ensure that the discharge conveyor can withstand the remaining temperature and material properties.
  3. Dust control: Hot and fine materials easily become airborne during the transfer phases. Plan the seals and any dust removal systems at this stage to ensure that the HSE requirements are met throughout the entire process chain.
  4. Cooling water circuit: Water-based cooling systems must include a plan for circulating cooling water, temperature control, and any leakage arrangements. Ensure that the water circuit is properly sized for peak load.
  5. Automation and control: Integrate the cooling system into the process automation. Temperature sensors, alarms, and remote monitoring capabilities improve operational reliability and enable predictive maintenance.

For operational reliability, it is also important to consider maintainability already at the design stage. A device that is easily accessible and whose wear parts can be replaced quickly keeps production running better than a theoretically more efficient but difficult to maintain solution. Modular structures, where individual parts can be turned or replaced without dismantling the entire device, significantly reduce maintenance downtime. Read more about it, How the sizing of the cooling system affects the equipment's lifetime.

Checklist: After you have gone through all the integration factors, you should have a clear picture of how the cooling solution fits into the broader process and what are the most critical points of concern. If any point remains unclear, it is worth clarifying it before purchasing the equipment, not after.

Kopar designs and supplies cooling solutions for the most demanding melting and mineral processing processes, from cooling screws and cooling drums to the high-performance rotary screw chillers of the KRC series. Each solution is tailored to the actual requirements of the process, and no ready-made standard solutions are pushed forward as such. Discover our cooling solutions or Contact our experts, So let’s go through together which solution best suits your specific process.

Kopar Service Manager

You have a challenge that needs solving?